Eco-friendly Packaging Film Series

The agricultural film on the market from different manufacturers, thickness, prices are bigger difference, should pay attention to the following three aspects: when buying first, first look at the product certificate, at the same time to pay attention to the appearance quality of river, the whole volume in bulk.
Good quality agricultural films is silvery white, the whole roll of uniform.

Good agricultural films, tensile strength of the horizontal and vertical are better;

second, to measure the width of the film.

Different crops, different ways of cover need different width of the film, too wide or too narrow.
In addition, also need to compare the film thickness.

Thickness is associated with plastic tensile load directly, so don't just consider the investment cost, and choose a thin film;

the third, to calculate the dosage, don't buy blindly.

Dosage is according to grow their own way, length of the ridge ridge, calculate a mu need how many meters mulch.

the correct use of agricultural film, not only can increase crop yields, but also can improve the life of the river, thus reducing the production cost.

So when use should be paid attention to the following: first, covering film, to ensure that the skeleton is smooth without a thorn, lest damage membrane, tectorial membrane when the holding pressure, had better use straw rope reinforcement, in case of strong wind.

In move, covering, jie film, film, prevent yank fierce pull, lest membrane is the scaffolding prick, by strong wind.

second, agricultural film damage when using, must immediately repair.
Repair method with hot glue.
Hot glue method is applicable for polyethylene film.

Virginity wash to dry first, then cut a little older than the fissure or hole in thin film on top of fissure or build a cellophane or cigarette in aluminum foil, with a red-hot iron bar back and forth on the cellophane paper or aluminum foil hot a few times, two thin film adhesion.

third, film after use must lay flat flushing timely, hang to dry in the shade.

When stored, sprinkle a layer of talcum powder first, and then roll it up, don't fold and weight.

u003cpu003e1: Water-soluble film productsu003c/pu003e As a new concept of environmentally friendly packaging materials, Pva polyvinyl alcohol series water-soluble films are widely used in water-soluble chemical products and water-soluble products in Europe, America, Japan and other countries. Packaging material. u003c/pu003eFor example: pesticides, fertilizers, dyes, detergents, water treatment agents, mineral additives, detergents, concrete additives, chemical reagents for photography and chemical reagents for garden care, etc. It can also be used asu003c/pu003e , Plant seed bags, clothing packaging bags, food and hospital washing bags, and other internal and external packaging products. u003c/pu003eTwo: The main features of the water-soluble film are as follows: u003c/pu003e1 It has the function of anti-counterfeiting packaging and is also used as the best tool for high-quality products to prevent counterfeiting, extending the life cycle of high-quality products;u003c/pu003e2 % The final products of degradation and degradation are CO2 and H2O, no harmful substances are produced; u003c/pu003e3 It is safe and convenient to use, avoiding direct contact with harmful substances by users;u003c/pu003e 4 It can be accurately measured to prevent waste;u003c/pu003e u003e5 Good strength, toughness and plasticity, can be bonded; good heat sealing performance. u003c/pu003e3: Precautions when using water-soluble filmu003c/pu003e1 When the water content of the product exceeds 5%, it is not suitable for water-soluble film packaging;u003c/pu003e2 When not in use, use PE film to make the remaining water-soluble Film encapsulation;u003c/pu003e3 Suitable conditions for use of water-soluble film: 15～33℃, 40～70%RH;u003c/pu003e4Strong alkali, strong acid, chlorine free radicals and other substances that can react with PVA (Such as borax, boric acid, etc.), it is recommended not to use water-soluble film packaging for such substances. u003c/pu003e5 When product quality or other technical problems occur during use, please contact the supplier in time for corresponding technical consultation and services. u003c/pu003eFour: Water-soluble film model; specificationsu003c/pu003e1 model Ahs-S (low temperature dissolving) that is 15 degrees water solubleu003c/pu003e 2 model Ahs-Q (high temperature dissolving) that 70 degrees water solubleu003c/pu003e pu003e3 Specifications Width 100cm, length 200m, 500m, 1000mu003c/pu003e4 Water-soluble film thickness 25um--80um (2.5 filaments-8 filaments)u003c/pu003e5 Water-soluble film can be customized Cut out products between 10cm-100cm. u003c/pu003e5: The water-soluble film can be made into various types and specifications of water-soluble bags according to customer needs. u003c/pu003eTel: 025-58126878/58063639 Fax: 025-52395778u003c/pu003eOur companyu003c/pu003eu003c/pu003e

In recent years, optical grade PET polyester film has been widely used. Especially in the manufacturing process of liquid crystal display, PET-type optical film is an indispensable material, such as diffusion film, brightness enhancement film, anti-glare film and so on. In fact, this depends on the characteristics of the PET optical film-high light transmittance, low haze, high brightness, non-yellowing, good adhesion, good flatness, no shading, high temperature resistance and ultraviolet radiation, good stiffness, Anti-burning, not easy to break, etc. Functional PET optical film is mainly obtained by coating various functional coatings on the surface of PET polyester film. According to the function of the coating, the coating can be divided into three categories, namely, protective coating, decorative coating and functional coating. Coating different coatings on PET polyester film can produce films with different functions. For example, anti-scratch and anti-static (106~108Ω) coatings are coated on the surface of PET polyester film to make PET screen protection film, which is used to protect the surface of mobile phone or computer screen. Coating a coating containing optical particles or glass beads on the PET polyester film can be made into an optical diffusion film, which can be used in the LCD panel backlight module, which can effectively eliminate the phenomenon of light and dark interlacing or dots, and improve the brightness of the light. The panel provides a uniform surface light source. Coating a resin system with particles on the surface of the PET polyester film can be made into an anti-glare film, which can be used in liquid crystal displays. Scattering to prevent the effect of tailing of the picture, etc. is a company specializing in the production of PET film with multiple functions, such as: transparent PET film, milky white PET film, release PET film, supply of PET motor film, etc. With a wide variety of products, affordable prices, and environmental protection, we provide customers with excellent quality and service based on the service tenet of excellence in production, honesty and trustworthiness in distribution, and warm and thoughtful service, and the spirit of assisting partners to achieve their own businesses. Interested parties welcome to inquire!